Mecha Wiring: Klon Centaur Layout

Wednesday, October 26, 2022

Klon Centaur Layout

The rock your repaired amp klone is an exact, part for part, meticulously crafted replica of the infamous transparent overdrive pedal. Created by bostonian bill finnegan in 1994, the pedal and its innovative circuit (which uses an ic max1044 voltage converter and two.

Klon Centaur clone parts layout and Klon Centaur klone

He even shows the very first gold klon centaur he made and admitted he'd sell it for the right price.

Klon centaur layout. The goal in designing this pcb was space efficiency: 1.1 klon centaur circuit layout. The voltage range on the second opamp is actually 27v, but the amount of clean headroom you'll.

Although the klon centaur circuit remained pretty much unchanged throughout its production run, bill finnegan did tweak a few component values. This time i felt brave and decided to try an artwork technique courtesy of “frequencycentral” over at freestompboxes.org (described in this thread). However, all the potentiometers, jacks and the battery are wired and hand.

I thought i gave it a good go being. When using an 18v supply, you should use a voltage divider to run the first opamp at 9v. The ktr is unique in its design layout and also has some bill finnegan humor built in.

Updated on january 27, 2022. If you want to forego the charge pump, the first opamp in the klon runs at 9v and the clipping of that opamp is part of the klon sound as you turn the gain up. Silicon schottky diodes replace the original's germanium parts.

I finally got around to boxing the centaur. The klon ktr represents a more affordable version to the famed klon centaur. This is likely because the pedal is fairly recent in origin but had a.

I built this using a modified board layout provided in shake's blog page, after being alerted to it by soulsonic. Transients are slightly less crisp. Here’s a layout i did for the klon centaur overdrive based on a schematic by soulsonic.

Based on madbean's sunking schematic. The electronics layout is interesting, with two circuit boards facing in toward each other. The charge pump is present in the original to keep the 2nd opamp fro.

I have owned 2 original klon's in the past and multiple klones over the years and i can say without a doubt that this centura is the closest in sound (and looks!). The tone is bang on! Compared to the klon, the horseman's tones are marginally less sparkly and a bit boomier below 200 hz.

Finnegan was essentially addressing the complaints some people had about the original klon centaur (“make ‘em smaller, make ‘em true bypass, and let me use a standard boss style ac adapter”). In the parts of the circuit where double side pcb are needed (tracks crossing), there are links (wired bridges) that make the manufacture easier and cheaper. In 1995, two of the 1uf capacitors in the signal path were increased to 4.7uf to allow more low frequencies through, and a 15k resistor was added to ‘sweeten’ the midrange.

A new revision of the klon layout has been done which is smaller and makes better use of the space, so if you want to build this i'd suggest using that layout instead which will also be easier to fit in a 1590b for those wanting to use a smaller box. There’s no shortage of centaur clones that fit in larger enclosures, but ours was made for the 1590b (1290ns)—though it’s just as much at home in a 125b if that’s your style. It is painstakingly crafted using the absolute best components with a deep devotion to perfection.

The phrase on top, “kindly remember, the ridiculous hype. Perhaps the most legendary (and expensive) guitar pedal of all times, the klon centaur was one of the first boutique stompboxes and proved that an overdrive could be much more than just distortion. By all accounts, the klon was the first pedal to ever become unobtanium.

Ceriatone uses the same circuit board layout and many of.

Klon Pcb Layout PCB Circuits